الوصف
PTO Shaft Ratchet Torque Limiter – SAS2 Series (with Splined Shaft)
The PTO Shaft Ratchet Torque Limiter – SAS2 Series (with Splined Shaft) is a premium-quality ratchet torque limiter specifically engineered for PTO (Power Take-Off) drive shaft systems used across agricultural, industrial, and forestry machinery. Also known as a PTO slip clutch, PTO safety clutch, or tractor PTO overload protector, this device safeguards your expensive equipment from damage caused by sudden torque overloads, obstructions, and operational jamming.
Available Models: SAS2
Torque Range: Torque: 800 Nm
Spline Options: 1 3/8″ Z6 (female & male)
Key Components: Circlip, Retaining washer, Dust guard ring, Push pin kit, Hub, Pawl kit (Qty.=16), Housing with yoke, Grease nipple
Technical Specifications & Dimensions
| Series | Setting Torque (Nm) | Spline (female) | Spline (male) | A (mm) | B (mm) | C (mm) |
|---|---|---|---|---|---|---|
| SAS2 | 800 | 1 3/8″Z6 | 1 3/8″Z6 | 161 | 21 | 38 |
* All dimensions in millimeters. Torque values in Newton-meters (Nm). Spline specifications follow ISO/ASAE standards. Contact us for custom configurations.
Key Features & Advantages
🛠
Universal PTO Compatibility
Standard 1 3/8″ Z6 spline interface fits all major tractor and implement PTO shafts without adapters or modification.
⛳
Sealed & Protected Design
Grease-lubricated internals with dust seals protect against contamination in harsh agricultural environments.
📈
Wide Torque Selection Range
Available in multiple torque ratings (800 Nm) to match virtually any PTO-driven implement requirement.
⚖
Safety Certified
Manufactured under ISO 9001:2015 quality management with CE marking for European and international compliance.
📦
Compact & Lightweight
Engineered for minimal additional length and weight on the PTO shaft, preserving driveline balance and clearance.
🔁
Multiple Output Configurations
Available in yoke, splined shaft, and flanged output variants to suit any installation requirement.
How It Works — Operating Principle
The ratchet torque limiter uses spring-loaded pawl kits that engage with a precision-machined ratchet ring inside the housing. Under normal conditions, the pawls lock into the ratchet profile and transmit full torque. When an overload occurs and torque exceeds the spring preload setting, the pawls are forced out of engagement, and the clutch slips with a characteristic clicking sound. Once the overload condition clears, the pawls automatically re-engage with the ratchet on the next revolution, restoring full torque transmission without any manual intervention. The number of pawls determines the smoothness of the ratcheting action and the overall torque capacity — more pawls provide smoother slipping and higher ratings.
Reset Method: Automatic — self-resetting after overload clears
Best Suited For: Equipment experiencing frequent, transient overloads where zero-downtime reset is critical
Typical Agricultural Application Scenarios
Rotary Mowers & Flail Mowers
Protects the mower gearbox from damage when blades strike hidden rocks, stumps, or metal debris. The torque limiter absorbs the shock load and prevents it from reaching the tractor PTO.
Hay Balers & Round Balers
Prevents baler mechanism damage during slug feeding, twine wrapping failures, or foreign object ingestion by disconnecting the driveline before damaging torque levels are reached.
Rotary Tillers & Cultivators
Guards the tiller gearbox and tractor PTO when tines encounter buried rocks, roots, or compacted soil layers that can generate extreme torque spikes.
Manure Spreaders
Protects the beater mechanism and gearbox from overload when encountering frozen clumps, foreign objects, or uneven material distribution in the hopper.
Feed Mixers & TMR Wagons
Safeguards the mixer auger drive from damage caused by twine wrap, frozen feed blocks, or excessive loading that generates torque beyond design limits.
Torque Limiter Type Comparison
| Feature | Ball Detent | Friction Disc | Shear Pin/Bolt | Ratchet (Pawl) | Automatic (Cam) |
|---|---|---|---|---|---|
| Torque Range | Low–Medium | Medium–High | Low–Very High | Low–High | Medium–High |
| Speed Range | 540–1000 RPM | 540–1000 RPM | 540–1000 RPM | 540–1000 RPM | 540–1000 RPM |
| Reset Method | Automatic | Automatic (slip) | Manual (replace bolt) | Automatic (ratchet) | Automatic (cam) |
| Best Application | Light implements | Frequent moderate overloads | Infrequent severe overloads | Frequent transient overloads | High-utilization, no consumables |
| Consumable Parts | None | Friction linings (long life) | Shear bolts | None | None |
| Torque Precision | Moderate | Good (adjustable) | Excellent (bolt-grade calibrated) | Good | Very Good (adjustable) |
Installation & Usage Guide
Installation Steps
Step 1: Verify that the PTO shaft spline size matches the torque limiter spline specification (1 3/8″ Z6 (female & male)). Clean all spline surfaces thoroughly.
Step 2: Slide the torque limiter onto the PTO shaft spline, ensuring full engagement. Secure with the provided push pin kit or retaining hardware.
Step 3: Connect the output side (yoke or splined shaft) to the implement input shaft or gearbox. Ensure proper alignment and secure all fasteners to the recommended torque.
Step 4: Apply grease through the grease nipple to lubricate the spline interface and internal components. Use lithium-based EP grease (NLGI #2).
Step 5: Perform a low-speed test run to verify correct engagement and smooth operation before full-power operation.
Safety & Maintenance Tips
⚠ Always disengage the tractor PTO before inspecting or servicing the torque limiter.
⚠ Use only genuine replacement parts specified for your series to maintain the correct torque rating.
⚠ Re-grease spline connections every 8 operating hours or as specified in your equipment manual.
⚠ Inspect for wear, cracks, or damage before each season. Replace worn components immediately.
⚠ Never operate with damaged or missing PTO shaft safety shields.
Selection Guide — Choosing the Right Model
Selecting the correct torque limiter requires confirming the following parameters:
✓ Required Torque Rating (Nm): Match the implement’s maximum operating torque plus a 20–30% safety margin.
✓ PTO Shaft Spline Size: Commonly 1 3/8″ Z6 (6-spline) or 1 3/4″ Z6/Z20. Verify both input and output spline requirements.
✓ PTO Speed: Standard 540 RPM or economy 1000 RPM — confirm your implement’s requirement.
✓ Connection Type: Yoke output for standard shaft tubes, splined shaft for inline assemblies, or flanged output for direct gearbox mounting.
✓ Overload Frequency: Frequent overloads favor auto-reset types (ratchet, friction, automatic). Infrequent but severe overloads suit shear bolt types.
✓ Environmental Conditions: Consider dust, moisture, temperature extremes. Sealed automatic and friction types offer superior protection in harsh environments.
Need help choosing? Contact our engineering team for personalized selection assistance.
Quality Certification & Service Commitment
✅
ISO 9001:2015
Certified quality management system ensuring consistent product excellence
✅
CE Marked
Compliant with European safety, health, and environmental protection standards
💪
12-Month Warranty
Full warranty against manufacturing defects under normal operating conditions
🚚
Global Shipping
Fast worldwide delivery with professional export packaging and documentation
Frequently Asked Questions (FAQ)
What Our Customers Say
🇦🇷 Miguel R. — Ranch manager, Buenos Aires Province, Argentina
“Outstanding durability in our dusty Pampas conditions. We’ve been using these for two years on grain augers and feed mixers with zero failures. The sealed design keeps the dust out.”
★★★★★
🇺🇸 David H. — Equipment dealer, Iowa, United States
“Our customers keep coming back for these. The quality matches or exceeds European OEM brands at a fraction of the cost. We stock the full range for combine, baler, and mower applications.”
★★★★★
🇳🇿 Craig W. — Dairy farmer, Waikato, New Zealand
“Using these on our pasture toppers and feed wagons. They’ve saved our PTO shafts from damage multiple times when hitting hidden stumps. Brilliant design — the auto-reset means we don’t lose any milking time.”
★★★★★
🇬🇧 William D. — Arable contractor, Yorkshire, United Kingdom
“Top-notch manufacturing quality. These drop straight onto standard UK PTO shafts and the torque ratings are spot-on. I’ve fitted them on cultivators, grain drills, and mowers — all performing perfectly.”
★★★★★
🇦🇺 James M. — Grain farmer, NSW, Australia
“We fitted these torque limiters on all our header drives after losing a gearbox last harvest. They’ve triggered twice on hidden rocks and saved us thousands in repairs each time. Absolutely essential equipment for Australian broadacre farming.”
★★★★★
Related PTO Shaft Products & Accessories
PTO Shaft Components
Complete range of PTO shaft yokes, cross bearings, tubes, shields, and adapters for all standard sizes.
Agricultural Gearboxes
Matched gearboxes designed to work seamlessly with our PTO shafts and torque limiters.
Available PTO Accessories:
• PTO shaft yokes (plain bore, splined, quick-release)
• Safety shields and guard tubes (EN 12965 compliant)
• Spline adapters (1 3/8″ to 1 3/4″ conversion)
• Cross bearing kits and U-joint repair kits
• Telescoping PTO shaft tubes (triangular and lemon profile)
• Push pin kits and retaining hardware
Ready to Protect Your Equipment?
Whether you need a single replacement unit or bulk OEM supply, our team is ready to help you select the perfect torque limiter for your application. We offer competitive B2B pricing, technical consultation, and fast global delivery.
Get a Free Quote →
Browse All Products
OEM & distributor partnerships welcome · MOQ as low as 10 units · Custom specifications available
